Shares 2

How To Bleed The Front Brake Master Cylinder Of A Motorcycle?

Last updated on 29-Apr-2024 , By Saleh

The braking system is a crucial component of any motorcycle, especially the front brake, which ensures safety and control over the motorcycle while riding. In the hydraulic braking system, moisture develops over time in the brake fluids, and air bubbles are produced in the brake line. As a result, riders experience a decrease in performance in brakes. Bleeding the brake master cylinder is a maintenance task that helps remove air bubbles from the system and restore optimal braking performance. In this article, we will have a brief discussion on how to bleed the front brake master cylinder of a motorcycle.

 

How To Bleed The Front Brake Master Cylinder Of A Motorcycle

The front brake is a crucial part of a motorcycle's braking system, and the master cylinder is a vital component of the motorcycle's hydraulic braking system. Therefore, to ensure optimal braking performance, it is essential to maintain the front braking assembly periodically, especially by bleeding the front brake master cylinder regularly.

Bleeding the master cylinder of the front braking system helps to drain out the air bubbles from the brake fluids inside the brake line. This results in a responsive braking action and better control over the motorcycle for the rider. Hence, here we have provided a step-by-step guide on how to bleed the front brake master cylinder of a motorcycle. So, do follow the procedure to maintain the workability of the braking system of your motorcycle.

Prepare The Tools And Idle The Motorcycle

Before attempting to bleed the front brake master cylinder, make sure you have the necessary tools and materials. These include a brake bleeding kit or plastic pipe, fresh brake fluid specified by the motorcycle manufacturer, clean rags, and a suitable container to collect the old brake fluid. Next, ensure that the motorcycle is securely parked on a level surface using the center stand or a paddock stand. Keep the motorcycle upright before working on the front brake.

Start Bleeding The Front Brake Master Cylinder

Next, identify the front brake master cylinder of your motorcycle. It is typically located near the handlebars and is connected to the brake lever. It is usually a cylindrical reservoir with a cap. Remove the cap and inspect the brake fluid level in the reservoir. Ensure it is above the minimum level but below the maximum level indicated on the reservoir. If necessary, top up the brake fluid to the correct level.

Then, locate the front brake caliper assembly attached to the wheel hub and connected with the brake line from the master cylinder. Also, locate the bleeder valves on the brake caliper. These valves are typically small metal nipples covered with rubber caps. If needed, refer to your motorcycle's manual to accurately locate the bleeder valves.

Take the clear plastic hose of the brake bleeding kit and attach one end tightly over the brake bleed screw. Make sure it fits securely to prevent any leaks. Place the other end of the hose into the clean container you have prepared for collecting the old brake fluid. Then, gently squeeze and hold the front brake lever. Loosen the brake bleed screw using the appropriate wrench or socket set. This will allow air and old brake fluid to escape through the hose into the container. After that, tighten the brake bleed screw back.

Repeat this process multiple times. As you maintain pressure on the brake lever, you should see a mixture of air bubbles and brake fluid flowing through the hose. Continue this process until you observe a steady stream of brake fluid without any air bubbles. Don't forget to refill the master cylinder from time to time. However, for this process, you can seek the help of a friend or assistant. After completing the bleeding process, check the fluid level in the master cylinder reservoir again. If it is low, top it up to the recommended level, close the reservoir cap, and you're done.

Final Check, Test Ride, And You're Done

Once you have finished the bleeding process of your motorcycle's front brake, clean the area around the brake master cylinder and brake caliper assembly. Wipe off any spilled brake fluid and clean it with water. Double-check that all bolts are tight and secure. Finally, give the brake lever a few gentle squeezes to ensure that it feels firm and responsive. If everything seems to be in order, take your motorcycle for a short test ride in a safe area to confirm that the brakes are functioning correctly.

Published by Saleh

Best Bikes

Honda CB Hornet 160R

Honda CB Hornet 160R

Price: 169800.00

Honda CB Hornet 160R ABS

Honda CB Hornet 160R ABS

Price: 255000.00

Honda CB Hornet 160R CBS

Honda CB Hornet 160R CBS

Price: 212000.00

View all Best Bikes

Latest Bikes

Honda SP160 (Single Disc)

Honda SP160 (Single Disc)

Price: 197000.00

Lifan Blues 150

Lifan Blues 150

Price: 0.00

Lifan KPV350

Lifan KPV350

Price: 0.00

View all Sports Bikes

Upcoming Bikes

Bajaj Freedom 125

Bajaj Freedom 125

Price: 0.00

Lifan K29

Lifan K29

Price: 0.00

455500

455500

Price: 0.00

View all Upcoming Bikes